Contenu du fichier

Bootdata ok (command line is root=/dev/sda1 ro console=tty0)
Linux version 2.6.18-6-xen-amd64 (Debian 2.6.18.dfsg.1-23etch1) (dannf@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Fri Dec 12 07:02:03 UTC 2008
BIOS-provided physical RAM map:
 Xen: 0000000000000000 - 00000000f3e1d000 (usable)
On node 0 totalpages: 998941
  DMA zone: 998941 pages, LIFO batch:31
DMI 2.4 present.
ACPI: RSDP (v002 DELL                                  ) @ 0x00000000000f25d0
ACPI: XSDT (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x00000000000f2650
ACPI: FADT (v003 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x00000000000f2758
ACPI: MADT (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x00000000000f284c
ACPI: SPCR (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x00000000000f292d
ACPI: HPET (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x00000000000f297d
ACPI: MCFG (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x00000000000f29b5
ACPI: DSDT (v001 DELL   PE_SC3   0x00000001 MSFT 0x0100000e) @ 0x0000000000000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] disabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x15] disabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x16] disabled)
ACPI: LAPIC (acpi_id[0x08] lapic_id[0x17] disabled)
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0x1])
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x05] address[0xfec81000] gsi_base[64])
IOAPIC[1]: apic_id 5, version 32, address 0xfec81000, GSI 64-87
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to xen
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at d1000000 (gap: d0000000:10000000)
Built 1 zonelists.  Total pages: 998941
Kernel command line: root=/dev/sda1 ro console=tty0
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Xen reported: 1862.066 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Software IO TLB enabled: 
 Aperture:     64 megabytes
 Kernel range: 0xffff88000612d000 - 0xffff88000a12d000
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Memory: 3824632k/3995764k available (1950k kernel code, 162228k reserved, 877k data, 148k init)
Calibrating delay using timer specific routine.. 4656.65 BogoMIPS (lpj=9313307)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
(SMP-)alternatives turned off
ACPI: Core revision 20060707
Initializing CPU#1
Initializing CPU#2
Brought up 4 CPUs
Initializing CPU#3
migration_cost=21
checking if image is initramfs... it is
Grant table initialized
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:11:0d.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST.DWN1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST.DWN2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.PE2P._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX6._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SBEX._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.COMP._PRT]
ACPI: PCI Interrupt Link [LK00] (IRQs 3 4 *5 6 7 10 11 12)
ACPI: PCI Interrupt Link [LK01] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK02] (IRQs 3 4 5 *6 7 10 11 12)
ACPI: PCI Interrupt Link [LK03] (IRQs 3 4 5 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LK04] (IRQs 3 4 5 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LK05] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK06] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LK07] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: ACPI device : hid PNP0A03
pnp: ACPI device : hid PNP0200
pnp: ACPI device : hid PNP0C04
pnp: ACPI device : hid PNP0C01
pnp: ACPI device : hid PNP0B00
pnp: ACPI device : hid PNP0700
pnp: ACPI device : hid PNP0501
pnp: ACPI device : hid PNP0501
pnp: ACPI device : hid PNP0C01
pnp: ACPI device : hid IPI0001
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0103
pnp: PnP ACPI: found 12 devices
xen_mem: Initialising balloon driver.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
pnp: the driver 'system' has been registered
pnp: match found with the PnP device '00:03' and the driver 'system'
pnp: match found with the PnP device '00:08' and the driver 'system'
pnp: 00:08: ioport range 0x800-0x87f could not be reserved
pnp: 00:08: ioport range 0x880-0x8bf has been reserved
pnp: 00:08: ioport range 0x8c0-0x8df has been reserved
pnp: 00:08: ioport range 0x8e0-0x8e3 has been reserved
pnp: 00:08: ioport range 0xc00-0xc7f has been reserved
pnp: 00:08: ioport range 0xca0-0xca7 has been reserved
pnp: 00:08: ioport range 0xca9-0xcab has been reserved
pnp: 00:08: ioport range 0xcad-0xcaf has been reserved
pnp: match found with the PnP device '00:09' and the driver 'system'
pnp: 00:09: ioport range 0xca8-0xca8 has been reserved
pnp: 00:09: ioport range 0xcac-0xcac has been reserved
pnp: match found with the PnP device '00:0a' and the driver 'system'
PCI: Bridge: 0000:08:00.0
  IO window: disabled.
  MEM window: d6000000-d9ffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:07:00.0
  IO window: disabled.
  MEM window: d6000000-d9ffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:07:01.0
  IO window: e000-efff
  MEM window: d5e00000-d5ffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:06:00.0
  IO window: e000-efff
  MEM window: d4000000-d9ffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:06:00.3
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:02.0
  IO window: e000-efff
  MEM window: d2000000-d9ffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:01:00.0
  IO window: disabled.
  MEM window: de800000-de9fffff
  PREFETCH window: f8000000-f80fffff
PCI: Bridge: 0000:01:00.2
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:03.0
  IO window: disabled.
  MEM window: de700000-de9fffff
  PREFETCH window: f8000000-f80fffff
PCI: Bridge: 0000:0c:00.0
  IO window: d000-dfff
  MEM window: de500000-de6fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:04.0
  IO window: d000-dfff
  MEM window: de300000-de6fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:05.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:06.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:07.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:04:00.0
  IO window: disabled.
  MEM window: da000000-ddffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.0
  IO window: disabled.
  MEM window: da000000-ddffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
  IO window: c000-cfff
  MEM window: de100000-de2fffff
  PREFETCH window: f0000000-f7ffffff
GSI 16 sharing vector 0xA0 and IRQ 16
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:02.0 to 64
ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:06:00.0 to 64
ACPI: PCI Interrupt 0000:07:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:07:00.0 to 64
PCI: Setting latency timer of device 0000:08:00.0 to 64
ACPI: PCI Interrupt 0000:07:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:07:01.0 to 64
PCI: Setting latency timer of device 0000:06:00.3 to 64
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:03.0 to 64
PCI: Setting latency timer of device 0000:01:00.0 to 64
PCI: Setting latency timer of device 0000:01:00.2 to 64
ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:04.0 to 64
ACPI: PCI Interrupt 0000:0c:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:0c:00.0 to 64
PCI: Setting latency timer of device 0000:00:05.0 to 64
ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:06.0 to 64
PCI: Setting latency timer of device 0000:00:07.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
PCI: Setting latency timer of device 0000:04:00.0 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1237467410.904:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
PCI: Setting latency timer of device 0000:00:03.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.0:pcie00]
PCI: Setting latency timer of device 0000:00:04.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
PCI: Setting latency timer of device 0000:00:05.0 to 64
pcie_portdrv_probe->Dev[25e5:8086] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:05.0:pcie00]
PCI: Setting latency timer of device 0000:00:06.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:06.0:pcie00]
PCI: Setting latency timer of device 0000:00:07.0 to 64
pcie_portdrv_probe->Dev[25e7:8086] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:07.0:pcie00]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
PCI: Setting latency timer of device 0000:06:00.0 to 64
Allocate Port Service[0000:06:00.0:pcie10]
PCI: Setting latency timer of device 0000:07:00.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:07:00.0:pcie20]
PCI: Setting latency timer of device 0000:07:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:07:01.0:pcie20]
Real Time Clock Driver v1.12ac
hpet_acpi_add: no address or irqs in _CRS
Linux agpgart interface v0.101 (c) Dave Jones
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
Xen virtual console successfully installed as ttyS0
Event-channel device installed.
pnp: the driver 'i8042 kbd' has been registered
pnp: the driver 'i8042 aux' has been registered
pnp: the driver 'i8042 kbd' has been unregistered
pnp: the driver 'i8042 aux' has been unregistered
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
processor: Unknown symbol pm_idle
thermal: Unknown symbol acpi_processor_set_thermal_limit
Intel(R) PRO/1000 Network Driver - version 7.1.9-k4-NAPI
Copyright (c) 1999-2006 Intel Corporation.
GSI 17 sharing vector 0xA8 and IRQ 17
ACPI: PCI Interrupt 0000:0a:00.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:0a:00.0 to 64
SCSI subsystem initialized
megasas: 00.00.03.01 Sun May 14 22:49:52 PDT 2006
e1000: 0000:0a:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x4) 00:15:17:5c:18:ac
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
USB Universal Host Controller Interface driver v3.0
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
GSI 18 sharing vector 0xB0 and IRQ 18
ACPI: PCI Interrupt 0000:0a:00.1[B] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:0a:00.1 to 64
e1000: 0000:0a:00.1: e1000_probe: (PCI Express:2.5Gb/s:Width x4) 00:15:17:5c:18:ad
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
megasas: 0x1028:0x0015:0x1028:0x1f03: <6>Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.4.44 (August 10, 2006)
bus 2:slot 14:func 0
ACPI: PCI Interrupt 0000:09:00.0[A] -> <6>GSI 19 sharing vector 0xB8 and IRQ 19
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 21 (level, low) -> IRQ 19
GSI 20 sharing vector 0xC0 and IRQ 20
ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 78 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xdea00000
GSI 16 (level, low) -> IRQ 16
eth2: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem d6000000, IRQ 16, node addr 001d090d8d7f
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
scsi0 : LSI Logic SAS based MegaRAID driver
  Vendor: SEAGATE   Model: ST973402SS        Rev: S207
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: SEAGATE   Model: ST973402SS        Rev: S207
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: SEAGATE   Model: ST9146802SS       Rev: S207
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: SEAGATE   Model: ST9146802SS       Rev: S207
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: SEAGATE   Model: ST9146802SS       Rev: S207
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: SEAGATE   Model: ST9146802SS       Rev: S207
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: SEAGATE   Model: ST9146802SS       Rev: S207
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: SEAGATE   Model: ST9146802SS       Rev: S207
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: DP        Model: BACKPLANE         Rev: 1.05
  Type:   Enclosure                          ANSI SCSI revision: 05
  Vendor: DELL      Model: PERC 5/i          Rev: 1.03
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: DELL      Model: PERC 5/i          Rev: 1.03
  Type:   Direct-Access                      ANSI SCSI revision: 05
ACPI: PCI Interrupt 0000:05:00.0[A] -> <6>ACPI: PCI Interrupt 0000:0d:04.0[A] -> GSI 16 (level, low) -> IRQ 16
GSI 16 (level, low) -> IRQ 16
eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem da000000, IRQ 16, node addr 001d090d8d7d
SCSI device sda: 142082048 512-byte hdwr sectors (72746 MB)
sda: Write Protect is off
sda: Mode Sense: 1f 00 10 08
SCSI device sda: drive cache: write through w/ FUA
SCSI device sda: 142082048 512-byte hdwr sectors (72746 MB)
sda: Write Protect is off
sda: Mode Sense: 1f 00 10 08
SCSI device sda: drive cache: write through w/ FUA
 sda: sda1 sda2 sda3 sda4
sd 0:2:0:0: Attached scsi disk sda
SCSI device sdb: 1141899264 512-byte hdwr sectors (584652 MB)
sdb: Write Protect is off
sdb: Mode Sense: 1f 00 10 08
SCSI device sdb: drive cache: write through w/ FUA
SCSI device sdb: 1141899264 512-byte hdwr sectors (584652 MB)
sdb: Write Protect is off
sdb: Mode Sense: 1f 00 10 08
SCSI device sdb: drive cache: write through w/ FUA
 sdb: sdb1
sd 0:2:1:0: Attached scsi disk sdb
usb 1-5: new high speed USB device using ehci_hcd and address 3
usb 1-5: configuration #1 chosen from 1 choice
hub 1-5:1.0: USB hub found
hub 1-5:1.0: 4 ports detected
scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
        <Adaptec AIC7902 Ultra320 SCSI adapter>
        aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs

  Vendor: IFT       Model: A08U-G2421        Rev: 347G
  Type:   Direct-Access                      ANSI SCSI revision: 05
 target1:0:0: asynchronous
scsi1:A:0:0: Tagged Queuing enabled.  Depth 32
 target1:0:0: Beginning Domain Validation
 target1:0:0: wide asynchronous
 target1:0:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS PCOMP (6.25 ns, offset 127)
 target1:0:0: Ending Domain Validation
sdc : very big device. try to use READ CAPACITY(16).
sdc : READ CAPACITY(16) failed.
sdc : status=0, message=00, host=5, driver=00 
sdc : use 0xffffffff as device size
SCSI device sdc: 4294967296 512-byte hdwr sectors (2199023 MB)
sdc: Write Protect is off
sdc: Mode Sense: 9b 00 00 08
SCSI device sdc: drive cache: write back
sdc : very big device. try to use READ CAPACITY(16).
sdc : READ CAPACITY(16) failed.
sdc : status=0, message=00, host=5, driver=00 
sdc : use 0xffffffff as device size
SCSI device sdc: 4294967296 512-byte hdwr sectors (2199023 MB)
sdc: Write Protect is off
sdc: Mode Sense: 9b 00 00 08
SCSI device sdc: drive cache: write back
 sdc: sdc1
sd 1:0:0:0: Attached scsi disk sdc
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 21 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 19, io base 0x0000bce0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
GSI 21 sharing vector 0xC8 and IRQ 21
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 20 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 21, io base 0x0000bcc0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 21 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 19, io base 0x0000bca0
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ESB2: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 16
ESB2: chipset revision 9
ESB2: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
usb 3-1: new low speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
hda: HL-DT-STDVD-ROM GDR-T10N, ATAPI CD/DVD-ROM drive
usbcore: registered new driver hiddev
input: Avocent Dell 03R874 as /class/input/input0
input: USB HID v1.10 Keyboard [Avocent Dell 03R874] on usb-0000:00:1d.1-1
input: Avocent Dell 03R874 as /class/input/input1
input: USB HID v1.10 Mouse [Avocent Dell 03R874] on usb-0000:00:1d.1-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 24X DVD-ROM drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
ts: Compaq touchscreen protocol output
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
input: PC Speaker as /class/input/input2
intel_rng: FWH not detected
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
8250_pnp: Unknown symbol serial8250_unregister_port
8250_pnp: Unknown symbol serial8250_register_port
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
8250_pnp: Unknown symbol serial8250_unregister_port
8250_pnp: Unknown symbol serial8250_register_port
floppy0: no floppy controllers found
Adding 3903784k swap on /dev/sda2.  Priority:-1 extents:1 across:3903784k
EXT3 FS on sda1, internal journal
loop: loaded (max 8 devices)
sd 1:0:0:0: Attempting to queue an ABORT message:CDB: 0x28 0x0 0x0 0x0 0x0 0x4b 0x0 0x0 0x2 0x0
scsi1: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State at program address 0x3b Mode 0x22
Card was paused
INTSTAT[0x0] SELOID[0x0] SELID[0x0] HS_MAILBOX[0x0] 
INTCTL[0x80]:(SWTMINTMASK) SEQINTSTAT[0x0] SAVED_MODE[0x11] 
DFFSTAT[0x33]:(CURRFIFO_NONE|FIFO0FREE|FIFO1FREE) 
SCSISIGI[0x24]:(P_DATAOUT_DT|BSYI) SCSIPHASE[0x0] 
SCSIBUS[0x0] LASTPHASE[0x1]:(P_DATAOUT|P_BUSFREE) 
SCSISEQ0[0x40]:(ENSELO) SCSISEQ1[0x12]:(ENAUTOATNP|ENRSELI) 
SEQCTL0[0x0] SEQINTCTL[0x0] SEQ_FLAGS[0x0] SEQ_FLAGS2[0x4]:(SELECTOUT_QFROZEN) 
QFREEZE_COUNT[0x1] KERNEL_QFREEZE_COUNT[0x1] MK_MESSAGE_SCB[0xff00] 
MK_MESSAGE_SCSIID[0xff] SSTAT0[0x10]:(SELINGO) 
SSTAT1[0x8]:(BUSFREE) SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0xc0]:(HIPERR|HIZERO) 
SIMODE1[0xac]:(ENSCSIPERR|ENBUSFREE|ENSCSIRST|ENSELTIMO) 
LQISTAT0[0x0] LQISTAT1[0x0] LQISTAT2[0x80]:(PACKETIZED) 
LQOSTAT0[0x0] LQOSTAT1[0x0] LQOSTAT2[0x40] 

SCB Count = 4 CMDS_PENDING = 1 LASTSCB 0x2 CURRSCB 0x3 NEXTSCB 0xffc0
qinstart = 115 qinfifonext = 115
QINFIFO:
WAITING_TID_QUEUES:
       0 ( 0x3 )
Pending list:
  3 FIFO_USE[0x0] SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] 
Total 1
Kernel Free SCB list: 2 1 0 
Sequencer Complete DMA-inprog list: 
Sequencer Complete list: 
Sequencer DMA-Up and Complete list: 
Sequencer On QFreeze and Complete list: 


scsi1: FIFO0 Free, LONGJMP == 0x8272, SCB 0x3
SEQIMODE[0x3f]:(ENCFG4TCMD|ENCFG4ICMD|ENCFG4TSTAT|ENCFG4ISTAT|ENCFG4DATA|ENSAVEPTRS) 
SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL) 
SG_CACHE_SHADOW[0x2]:(LAST_SEG) SG_STATE[0x0] DFFSXFRCTL[0x0] 
SOFFCNT[0x0] MDFFSTAT[0x5]:(FIFOFREE|DLZERO) SHADDR = 0x00, SHCNT = 0x0 
HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]:(SG_CACHE_AVAIL) 

scsi1: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
SEQIMODE[0x3f]:(ENCFG4TCMD|ENCFG4ICMD|ENCFG4TSTAT|ENCFG4ISTAT|ENCFG4DATA|ENSAVEPTRS) 
SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL) 
SG_CACHE_SHADOW[0x2]:(LAST_SEG) SG_STATE[0x0] DFFSXFRCTL[0x0] 
SOFFCNT[0x0] MDFFSTAT[0x5]:(FIFOFREE|DLZERO) SHADDR = 0x00, SHCNT = 0x0 
HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]:(SG_CACHE_AVAIL) 
LQIN: 0x8 0x0 0x0 0x3 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 
scsi1: LQISTATE = 0x1, LQOSTATE = 0x1a, OPTIONMODE = 0x52
scsi1: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
scsi1: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0

SIMODE0[0xc]:(ENOVERRUN|ENIOERR) 
CCSCBCTL[0x4]:(CCSCBDIR) 
scsi1: REG0 == 0x3, SINDEX = 0x102, DINDEX = 0x102
scsi1: SCBPTR == 0xff03, SCB_NEXT == 0xff00, SCB_NEXT2 == 0x0
CDB 3 1 0 0 0 0
STACK: 0x24 0x0 0x0 0x0 0x0 0x0 0x0 0x0
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi1:0:0:0: Cmd aborted from QINFIFO
sd 1:0:0:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
scsi1: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State at program address 0x2 Mode 0x22
Card was paused
INTSTAT[0x0] SELOID[0x0] SELID[0x0] HS_MAILBOX[0x0] 
INTCTL[0x80]:(SWTMINTMASK) SEQINTSTAT[0x0] SAVED_MODE[0x11] 
DFFSTAT[0x33]:(CURRFIFO_NONE|FIFO0FREE|FIFO1FREE) 
SCSISIGI[0x24]:(P_DATAOUT_DT|BSYI) SCSIPHASE[0x0] 
SCSIBUS[0x0] LASTPHASE[0x1]:(P_DATAOUT|P_BUSFREE) 
SCSISEQ0[0x40]:(ENSELO) SCSISEQ1[0x12]:(ENAUTOATNP|ENRSELI) 
SEQCTL0[0x0] SEQINTCTL[0x0] SEQ_FLAGS[0x0] SEQ_FLAGS2[0x4]:(SELECTOUT_QFROZEN) 
QFREEZE_COUNT[0x1] KERNEL_QFREEZE_COUNT[0x1] MK_MESSAGE_SCB[0xff00] 
MK_MESSAGE_SCSIID[0xff] SSTAT0[0x10]:(SELINGO) 
SSTAT1[0x8]:(BUSFREE) SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0xc0]:(HIPERR|HIZERO) 
SIMODE1[0xac]:(ENSCSIPERR|ENBUSFREE|ENSCSIRST|ENSELTIMO) 
LQISTAT0[0x0] LQISTAT1[0x0] LQISTAT2[0x80]:(PACKETIZED) 
LQOSTAT0[0x0] LQOSTAT1[0x0] LQOSTAT2[0x40] 

SCB Count = 4 CMDS_PENDING = 0 LASTSCB 0x2 CURRSCB 0x3 NEXTSCB 0xffc0
qinstart = 115 qinfifonext = 116
QINFIFO: 0x3
WAITING_TID_QUEUES:
Pending list:
  3 FIFO_USE[0x0] SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] 
Total 1
Kernel Free SCB list: 2 1 0 
Sequencer Complete DMA-inprog list: 
Sequencer Complete list: 
Sequencer DMA-Up and Complete list: 
Sequencer On QFreeze and Complete list: 


scsi1: FIFO0 Free, LONGJMP == 0x8272, SCB 0x3
SEQIMODE[0x3f]:(ENCFG4TCMD|ENCFG4ICMD|ENCFG4TSTAT|ENCFG4ISTAT|ENCFG4DATA|ENSAVEPTRS) 
SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL) 
SG_CACHE_SHADOW[0x2]:(LAST_SEG) SG_STATE[0x0] DFFSXFRCTL[0x0] 
SOFFCNT[0x0] MDFFSTAT[0x5]:(FIFOFREE|DLZERO) SHADDR = 0x00, SHCNT = 0x0 
HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]:(SG_CACHE_AVAIL) 

scsi1: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
SEQIMODE[0x3f]:(ENCFG4TCMD|ENCFG4ICMD|ENCFG4TSTAT|ENCFG4ISTAT|ENCFG4DATA|ENSAVEPTRS) 
SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL) 
SG_CACHE_SHADOW[0x2]:(LAST_SEG) SG_STATE[0x0] DFFSXFRCTL[0x0] 
SOFFCNT[0x0] MDFFSTAT[0x5]:(FIFOFREE|DLZERO) SHADDR = 0x00, SHCNT = 0x0 
HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]:(SG_CACHE_AVAIL) 
LQIN: 0x8 0x0 0x0 0x3 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 
scsi1: LQISTATE = 0x1, LQOSTATE = 0x1a, OPTIONMODE = 0x52
scsi1: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
scsi1: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0

SIMODE0[0xc]:(ENOVERRUN|ENIOERR) 
CCSCBCTL[0x4]:(CCSCBDIR) 
scsi1: REG0 == 0x3, SINDEX = 0x102, DINDEX = 0x102
scsi1: SCBPTR == 0xff03, SCB_NEXT == 0xff00, SCB_NEXT2 == 0x0
CDB 3 1 0 0 0 0
STACK: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi1:0:0:0: Cmd aborted from QINFIFO
sd 1:0:0:0: Attempting to queue a TARGET RESET message:CDB: 0x28 0x0 0x0 0x0 0x0 0x4b 0x0 0x0 0x2 0x0
scsi1: Device reset code sleeping
scsi1: Device reset timer expired (active 1)
scsi1: Device reset returning 0x2003
Recovery SCB completes
sd 1:0:0:0: scsi: Device offlined - not ready after error recovery
sd 1:0:0:0: SCSI error: return code = 0x00020000
end_request: I/O error, dev sdc, sector 75
sd 1:0:0:0: rejecting I/O to offline device
sd 1:0:0:0: rejecting I/O to offline device
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6 over IPv4 tunneling driver
processor: Unknown symbol pm_idle
ACPI: Power Button (FF) [PWRF]
processor: Unknown symbol pm_idle
thermal: Unknown symbol acpi_processor_set_thermal_limit
bnx2: eth0 NIC Link is Up, 1000 Mbps full duplex
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Breaking affinity for irq 259
Breaking affinity for irq 260
Breaking affinity for irq 261
Breaking affinity for irq 265
Breaking affinity for irq 266
Breaking affinity for irq 267
Breaking affinity for irq 262
Breaking affinity for irq 263
Breaking affinity for irq 264
Bridge firewalling registered
device vif0.2 entered promiscuous mode
audit(1237467503.129:2): dev=vif0.2 prom=256 old_prom=0 auid=4294967295
xenbr2: port 1(vif0.2) entering learning state
ADDRCONF(NETDEV_UP): peth2: link is not ready
xenbr2: topology change detected, propagating
xenbr2: port 1(vif0.2) entering forwarding state
e1000: peth2: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
ADDRCONF(NETDEV_CHANGE): peth2: link becomes ready
device peth2 entered promiscuous mode
audit(1237467503.141:3): dev=peth2 prom=256 old_prom=0 auid=4294967295
xenbr2: port 2(peth2) entering learning state
xenbr2: topology change detected, propagating
xenbr2: port 2(peth2) entering forwarding state
device vif0.3 entered promiscuous mode
audit(1237467503.269:4): dev=vif0.3 prom=256 old_prom=0 auid=4294967295
xenbr3: port 1(vif0.3) entering learning state
ADDRCONF(NETDEV_UP): peth3: link is not ready
xenbr3: topology change detected, propagating
xenbr3: port 1(vif0.3) entering forwarding state
e1000: peth3: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
ADDRCONF(NETDEV_CHANGE): peth3: link becomes ready
device peth3 entered promiscuous mode
audit(1237467504.293:5): dev=peth3 prom=256 old_prom=0 auid=4294967295
xenbr3: port 2(peth3) entering learning state
xenbr3: topology change detected, propagating
xenbr3: port 2(peth3) entering forwarding state
device vif1.0 entered promiscuous mode
audit(1237467507.465:6): dev=vif1.0 prom=256 old_prom=0 auid=4294967295
ADDRCONF(NETDEV_UP): vif1.0: link is not ready
ip_tables: (C) 2000-2006 Netfilter Core Team
eth0: no IPv6 routers present
ADDRCONF(NETDEV_CHANGE): vif1.0: link becomes ready
xenbr2: port 3(vif1.0) entering learning state
xenbr2: topology change detected, propagating
xenbr2: port 3(vif1.0) entering forwarding state
device vif2.0 entered promiscuous mode
audit(1237467515.926:7): dev=vif2.0 prom=256 old_prom=0 auid=4294967295
ADDRCONF(NETDEV_UP): vif2.0: link is not ready
xenbr3: port 3(vif2.0) entering disabled state
device vif2.0 left promiscuous mode
audit(1237467711.554:8): dev=vif2.0 prom=0 old_prom=256 auid=4294967295
xenbr3: port 3(vif2.0) entering disabled state